Datakom DKG-307 Manual de usuario Pagina 23
- Pagina / 29
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
DKG-307 User Manual V-01.03
(14.02.2006)
- 23 -
SPARE-2 FAULT INPUT
Pgm Description Std
119 Operation 2
0: Alarm (the engine stops and horn relay operates))
2: Warning (the horn relay operates)
3: No operation
120 Fault monitoring 0
0: Always
1: After holdoff timer
2: When mains present
121 Latching 0
0: Non latching
1: Latching
122 Contact type 0
0: Normally open
1: Normally closed
123 Switching 0
0: Battery negative
1: Battery positive
124 Response delay 0
0: No delay
1: Delayed (4sec)
PROGRAM LOCK INPUT
Pgm Description Std
125 Operation 3
0: Alarm (the engine stops and horn relay operates))
2: Warning (the horn relay operates)
3: No operation
126 Fault monitoring 0
0: Always
1: After holdoff timer
2: When mains present
127 Latching 0
0: Non latching
1: Latching
128 Contact type 0
0: Normally open
1: Normally closed
129 Switching 0
0: Battery negative
1: Battery positive
130 Response delay 0
0: No delay
1: Delayed (4sec)
Parameters from P_131 to P_142 define the ohm-bar characteristics of the oil pressure sender.
The sender characteristics will be defined using maximum 6 points. The values should be entered in the
increasing order of ohm values. For unused points, ohm values should be entered as 0. An example table
is given below. The sensor characteristics used in this table are:
0.0 bar.......240 ohms
1.0 bar........218 ohms
5.0 bar........153 ohms
10.0 bar......103 ohms
Pgm Description Unit Value
131 Point_1 resistor ohm 103
132 Point_1 pressure bar 10.0
133 Point_2 resistor ohm 153
134 Point_2 pressure Bar 5.0
135 Point_3 resistor Ohm 218
136 Point_3 pressure Bar 1.0
137 Point_4 resistor Ohm 240
138 Point_4 pressure Bar 0.0
139 Point_5 resistor Ohm 0
140 Point_5 pressure Bar 0.0
141 Point_6 resistor Ohm 0
142 Point_6 pressure bar 0.0
- REMOTE START UNIT 1
- TABLE OF CONTENTS 2
- - 3 3
- - 4 4
- 2. INPUTS AND OUTPUTS 5
- - 6 6
- 3. DISPLAYS 7
- 3.1 Led Displays 7
- 3.2 Digital Displays 8
- 4. ALARMS AND WARNINGS 9
- 5. MODES OF OPERATION 10
- 6. OTHER FEATURES 10
- 6.1 Remote Start Operation 10
- 6.2 Sender type Selection 11
- 6.3 Engine Heating Operation 11
- 6.4 Service Request Display 12
- 6.5 Engine Hour Meter 12
- 6.6 Modem Connection 12
- 6.8 Exerciser 13
- 7. WEEKLY OPERATION SCHEDULE 14
- - 15 15
- 10. PROGRAMMING 16
- - 17 17
- - 18 18
- - 19 19
- - 20 20
- - 21 21
- - 22 22
- - 23 23
- - 24 24
- - 25 25
- 12. TROUBLESHOOTING 26
- - 27 27
- 14. TECHNICAL SPECIFICATIONS 28
- 15. CONNECTION DIAGRAM 29
AEG CD přehrávače uživatelské příručky
Začínající na S
Comentarios a estos manuales